Elcometer CG100ABDL Corrosion Thickness Gauges (0.01~508mm, A-scan, B-scan, Thrupaint, Datalogging)
Manufacturer: ELCOMETER Model: CG100ABDL - Contact
Measurement Mode: PE, PETP, EE, EEV, CT, PECT
A-Scan Display: + Rectified, - Rectified, Full Waveform (RF)
Measurement Rate:
+ 4 readings per second
+ 50 readings per second
+ 6 readings per second
Measuring Range
+ PE: 0.63 - 508mm
+ PETP: 0.63 - 508mm
+ EEV: 1.27 - 25.4mm
+ PECT: 0.63 - 508mm
+ PECT: 0.01 - 2.54mm
Calibration Options: Single, two point, velocity & material type
Measurement Accuracy: ± 1% or ±0.1mm
Measurement Resolution: 0.01 mm
Velocity Calibration Range: 1250 - 9,999m/s
B-Scan display speed: 15 seconds per screen
Datalogging: yes
Transducer Frequency Range: 1 - 10MHz
Display: 1/8 inch VGA, Display Refresh Rate 25Hz
Battery Type: 3 x AA alkaline
Battery Life: 150 hours
Operating Temperature: -10 to 60ºC
Size (w x h x d): 63.5 x 165.0 x 31.5mm
Weight (including batteries): 383g
RS232 Interface: Bi-directional
Packing List: Elcometer NDT CG100ABDL gauge, couplant, carry case, user manual, test certificate, 3 x AA batteries, ElcoMaster® software, transfer cable
Note: A transducer is not suppied with the Gauges, must be ordered separately (below options)
CG100 Corrosion Thickness Gauges
With a wide selection of display and measurement modes, automatic gain control and data-logging, the CG100 range of corrosion thickness gauges is ideal for measuring coating and material thickness as well as for locating pits, flaws and defects in materials.
The Elcometer CG100 ultrasonic corrosion thickness gauge is available in four models - from an entry level CG100B to the top of the range CG100ABDL+.
Features:
|
CG100 Corrosion Thickness Gauges
Technical Specification
Model & Part Number |
CG100B |
CG100BDL |
CG100ABDL |
CG100ABDL+ |
Material thickness digits display |
■ |
■ |
■ |
■ |
B-Scan cross sectional display |
■ |
■ |
■ |
■ |
Combined B-Scan and digits display |
■ |
■ |
■ |
■ |
Scan bar display |
■ |
■ |
■ |
■ |
Coating thickness display |
■ |
■ |
■ |
■ |
A-Scan Display |
|
|
+ Rectified, - Rectified, |
+ Rectified, - Rectified, |
Measurement Mode |
PE, PETP (Temp Compensation), |
PE, PETP (Temp Compensation), |
PE, PETP (Temp Compensation), |
PE, PETP (Temp Compensation), |
Measurement Rate |
4 readings per second |
4 readings per second |
4 readings per second |
4 readings per second |
Measuring Range |
PE: 0.63 - 508mm |
PE: 0.63 - 508mm |
PE: 0.63 - 508mm |
PE: 0.63 - 508mm |
Measurement Accuracy |
± 1% or ±0.1mm |
± 1% or ±0.1mm |
± 1% or ±0.1mm |
± 1% or ±0.1mm |
Measurement Resolution |
0.01mm (0.001 inches) |
0.01mm (0.001 inches) |
0.01mm (0.001 inches) |
0.01mm (0.001 inches) |
Velocity Calibration Range |
1250 - 13,995m/s |
1250 - 13,995m/s |
1250 - 13,995m/s |
1250 - 13,995m/s |
Additional Features: |
■ |
■ |
■ |
■ |
Differential mode |
■ |
■ |
■ |
■ |
Limit alarm mode |
■ |
■ |
■ |
■ |
B-Scan display speed |
15 seconds per screen |
15 seconds per screen |
Adjustable display speed |
Adjustable display speed |
Flaw mode |
|
|
Basic prove-up flaw detection using single element angle beam transducers |
Basic prove-up flaw detection using single element angle beam transducers |
Calibration setups |
6 factory & 64 user-definable setups transferrable to and from a PC archive |
6 factory & 64 user-definable setups transferrable to and from a PC archive |
6 factory & 64 user-definable setups transferrable to and from a PC archive |
6 factory & 64 user-definable setups transferrable to and from a PC archive |
Gates |
|
|
3 fully adjustable gates: start, stop, width & threshold |
3 fully adjustable gates: start, stop, width & threshold |
Damping |
|
|
|
Adjustable; impedance matching for optimising transducer performance |
Pulser type |
Dual square wave pulsers up to 140Hz pulse repetition rate |
Dual square wave pulsers up to 140Hz pulse repetition rate |
Dual 200 volt square wave pulsers with adjustable pulse width(spike, thin, wide) and 50 volt cut/boost for greater penetration |
Dual 200 volt square wave pulsers with adjustable pulse width |
Gain |
Automatic gain control (AGC) with 110dB range (limited), or selectable gain: vlow, low, medium hi or vhi |
Automatic gain control (AGC) with 110dB range (limited), or selectable gain: vlow, low, medium hi or vhi |
Manual, automatic gain control (AGC) with 110dB range (limited) |
Manual, automatic gain control (AGC) with 110dB range (limited) |
Timing |
Precision 25MHz TCXO with single shot 100MHz 8bit ultra low power 8 bit digitizer |
Precision 25MHz TCXO with single shot 100MHz 8bit ultra low power 8 bit digitizer |
Precision 25MHz TCXO with single shot 100MHz 8bit ultra low power 8 bit digitizer |
Precision 25MHz TCXO with single shot 100MHz 8bit ultra low power 8 bit digitizer |
Data logging |
|
|
|
|
Calibration Options |
Single, two point, velocity & material type |
Single, two point, velocity & material type |
Single, two point, velocity & material type |
Single, two point, velocity & material type |
Transducer Probe Type |
Dual element |
Dual element |
Dual element & flaw prove up |
Dual element & flaw prove up |
Transducer Frequency Range |
1 - 10MHz |
1 - 10MHz |
1 - 10MHz |
1 - 10MHz |
Transducer recognition |
Automatic & manual - selectable from a list |
Automatic & manual - selectable from a list |
Automatic & manual - selectable from a list |
Automatic & manual - selectable from a list |
V-path / dual path error correction |
Automatic |
Automatic |
Automatic |
Automatic |
Probe zero |
Automatic & manual (via integrated probe disk) |
Automatic & manual (via integrated probe disk) |
Automatic & manual (via integrated probe disk) |
Automatic & manual (via integrated probe disk) |
Display |
1/8 VGA (grayscale) |
1/8 VGA (grayscale) |
1/8 VGA (grayscale) |
1/4 VGA AMOLED colour display |
Display Refresh Rate |
25Hz |
25Hz |
25Hz |
120Hz |
Units (selectable) |
mm or inches |
mm or inches |
mm or inches |
mm or inches |
Backlight |
on / off / auto |
on / off / auto |
on / off / auto |
adjustable brightness |
Repeatability / Stability Indicator |
■ |
■ |
■ |
■ |
Battery Type |
3 x AA alkaline |
3 x AA alkaline |
3 x AA alkaline |
3 x AA alkaline |
Battery Life (approximate) |
150 hours |
150 hours |
50 hours |
25 hours |
Low Battery Indicator |
■ |
■ |
■ |
■ |
Battery Save Mode |
auto |
auto |
auto |
auto |
Operating Temperature |
-10 to 60ºC (14 to 140ºF) |
-10 to 60ºC (14 to 140ºF) |
-10 to 60ºC (14 to 140ºF) |
-10 to 60ºC (14 to 140ºF) |
Size (w x h x d) |
<td style="border:solid windowtext 1.0pt;mso-border-alt:solid windowtext .5pt;
padding:.75pt
- Quality Engagement
- Easy change and return
- Delivery Avaliable
- Favorable payment