For full functionality of this site it is necessary to enable JavaScript.
EMIN.COM.MM
0

Đừng Lát Sàn Gỗ Nếu Chưa Đo Độ Ẩm Nền Bê Tông

07/15/2026 14:58:59

Máy đo độ ẩm bê tông được thực hiện ngay trước khi thi công thay vì chờ đến khi phát sinh hư hỏng. Chỉ mất vài phút kiểm tra nhưng có thể tránh được việc tháo dỡ và thay thế toàn bộ sàn sau này.

Construction engineers often rely on a concrete moisture meter to determine the right time to install wood flooring.

Concrete does not become completely dry as soon as it reaches its design strength. Moisture trapped inside the slab continues to evaporate over an extended period, and the drying rate depends on weather conditions, ventilation, and the thickness of the concrete slab.

A newly installed wood floor usually shows no visible signs of trouble. The surface appears flat, the boards fit tightly together, and the installation is considered satisfactory. However, after several months of use, certain areas may begin to swell, produce squeaking sounds, or develop gaps between the boards.

On projects carried out during the rainy season, on ground floors, or in poorly ventilated areas, this drying process often takes longer than expected.

Why Does Wood Flooring Start to Swell Only After Several Months?

During the early stages, moisture migrates slowly from the concrete slab into the flooring, so there are typically no obvious signs of damage. Over time, however, the wood absorbs additional moisture, expands, and places stress on the locking joints. As a result, edge lifting, slight warping, and squeaking gradually begin to appear.

Wood floor swelling after several months is not always caused by poor-quality materials or improper installation. Residual moisture within the concrete subfloor is also a major factor that directly affects the long-term stability of the flooring system.

Visual Inspection Is Not Enough to Evaluate a Concrete Subfloor

On many construction projects, the installation schedule often determines when flooring work begins. As soon as the concrete surface feels hard enough and appears dry, finishing work typically proceeds.

However, the amount of moisture remaining inside the concrete cannot be assessed by visual inspection alone. When measured with a concrete floor moisture meter, it can be observed that the rate of moisture evaporation is slower in areas near the base of walls, close to utility boxes, or on the ground floor compared to the rest of the building.

Concrete Moisture Meters Are Becoming Part of Construction Quality Inspections

During site preparation, technicians measure moisture at multiple locations to evaluate the consistency of the subfloor. Areas with a history of water intrusion or those located near entrances are typically inspected more carefully.

Some projects also measure the moisture content of the wood flooring before installation to minimize the difference between the flooring material and the surrounding environment. Comparing these two measurements helps reduce the risk of warping, swelling, and other moisture-related issues after the floor is put into service.

A building material moisture meter provides quantitative measurements of the moisture content in concrete, cement, brick, mortar, and various types of wood. The results help determine whether the subfloor is ready for installation or requires additional drying time. For projects with stringent quality requirements, these measurements are often documented as part of the final inspection records for future verification or warranty purposes.

Using a concrete moisture meter before installation provides an accurate assessment of the subfloor condition. When both the concrete slab and flooring materials have reached appropriate moisture levels, the likelihood of warping, edge lifting, floor swelling, and expensive repairs can be significantly reduced

Related News

SMEMA standard for PCB conveyors
11/16/2026 14:00:39

SMEMA was developed to address this specific point; consequently, conveyors, loaders, and unloaders all include an SMEMA port in their technical specifications

Homes on busy streets: How to measure fine particulate matter and exhaust fumes entering your living room
11/16/2026 09:42:31

Living in a house facing a main road is particularly frustrating: you might wipe the tables until they’re spotless in the morning, only to find them covered in a layer of dust by the afternoon. Even with the doors tightly shut and the curtains drawn, the house still feels stuffy by evening—permeated by the faint, lingering presence of vehicle exhaust. While regular dust can be swept away, fine particulate matter the kind you can’t even see silently seeps in through the gaps around your doors and windows. So, before you rush to spend money on an air purifier or weather-stripping, take a moment to check the current air quality inside your home and identify exactly where the pollutants are entering

Can Laser Welding Machines Weld Aluminum Effectively ?
11/16/2026 08:54:12

Laser welding is presented as an aluminum-joining method that concentrates heat at the weld point, helping limit distortion. Suitable settings depend on material thickness, filler wire use, and trial weld results.

Stay Updated with Offers

Get exclusive volume discounts, bulk pricing updates, and new product alerts delivered directly to your inbox.

By subscribing, you agree to our Terms of Service and Privacy Policy.

Quick Support

Direct access to our certified experts